Belajar mengkonfigurasi ospfv3 di router cisco
topology yang digunakan adalah sebagai berikut:
(area0)
+------+ +------+
!(cnc2)! :1 11::11:/64 :2!(cnc3)!
! R2 !---------------------------! R3 !
! ! f1/0 f1/0 ! !
+------+ +------+
:1!f0/0 :1!f0/0
! !
(area2)!10::10:/64 (area3)!12::12:/64
! !
:2!f0/0 :2!f0/0
+------+ +------+
!(cnc1)! !(cnc4)!
! R1 ! ! R4 !
! ! ! !
+------+ +------+
by:
-https://iwing.wordpress.com
-http://www.ittelkom.ac.id/pinguin
Langkah-langkahnya adalah sebagai berikut :
Di router 1 (cnc1)
---------------------------------------------
cnc1(config)#int f0/0
cnc1(config-if)#ipv6 add 10::10:2/64
cnc1(config-if)#no shut
cnc1(config)#ipv6 unicast-routing
cnc1(config)#ipv6 router ospf 1
cnc1(config-rtr)#router-id 1.1.1.1
cnc1(config-rtr)#exit
cnc1(config)#
cnc1(config)#int f0/0
cnc1(config-if)#ipv6 ospf 1 a 2
cnc1(config-if)#
---------------------------------------------
Di router 2 (cnc2)
---------------------------------------------
cnc2(config)#int f0/0
cnc2(config-if)#ipv6 add 10::10:1/64
cnc2(config-if)#no shut
cnc2(config-if)#
cnc2(config-if)#int f1/0
cnc2(config-if)#ipv6 add 11::11:1/64
cnc2(config-if)#no shut
cnc2(config-if)#exit
cnc2(config)#ipv6 unicast-routing
cnc2(config)#ipv6 router ospf 1
cnc2(config-rtr)#router-id 2.2.2.2
cnc2(config-rtr)#exit
cnc2(config)
cnc2(config)#int f0/0
cnc2(config-if)#ipv6 ospf 1 a 2
cnc2(config)#int f1/0
cnc2(config-if)#ipv6 ospf 1 a 0
cnc2(config-if)#
---------------------------------------------
Di router 3 (cnc3)
---------------------------------------------
cnc3(config)#int f1/0
cnc3(config-if)#ipv6 add 11::11:2/64
cnc3(config-if)#no shut
cnc3(config-if)#int f0/0
cnc3(config-if)#ipv6 add 12::12:1/64
cnc3(config-if)#no shut
cnc3(config)#ipv6 unicast-routing
cnc3(config)#ipv6 router ospf 1
cnc3(config-rtr)#router-id 3.3.3.3
cnc3(config-rtr)#exit
cnc3(config)#
cnc3(config)#int f1/0
cnc3(config-if)#ipv6 ospf 1 a 0
cnc3(config-if)#int f0/0
cnc3(config-if)#ipv6 ospf 1 a 3
cnc3(config-if)#
---------------------------------------------
Di router 3 (cnc4)
---------------------------------------------
cnc4(config)#int f0/0
cnc4(config-if)#ipv6 add 12::12:2/64
cnc4(config-if)#no shut
cnc4(config)#ipv6 unicast-routing
cnc4(config)#cnc4(config)#ipv6 router ospf 1
cnc4(config-rtr)#router-id 4.4.4.4
cnc4(config-rtr)#exit
cnc4(config)#
cnc4(config)#int f0/0
cnc4(config-if)#ipv6 ospf 1 a 3
cnc4(config-if)#
---------------------------------------------
how to check 1 (sh ipv6 ospf neighbor)
---------------------------------------------
cnc1#sh ipv6 ospf neighbor
Neighbor ID Pri State Dead Time Interface ID Interface
2.2.2.2 1 FULL/BDR 00:00:34 4 FastEthernet0/0
cnc1#
cnc2#sh ipv6 ospf neighbor
Neighbor ID Pri State Dead Time Interface ID Interface
3.3.3.3 1 FULL/BDR 00:00:36 5 FastEthernet1/0
1.1.1.1 1 FULL/DR 00:00:34 4 FastEthernet0/0
cnc2#
cnc3#sh ipv6 ospf neighbor
Neighbor ID Pri State Dead Time Interface ID Interface
2.2.2.2 1 FULL/DR 00:00:36 5 FastEthernet1/0
4.4.4.4 1 FULL/BDR 00:00:30 4 FastEthernet0/0
cnc3#
cnc4#sh ipv6 ospf neighbor
Neighbor ID Pri State Dead Time Interface ID Interface
3.3.3.3 1 FULL/DR 00:00:34 4 FastEthernet0/0
cnc4#
---------------------------------------------
how to check 2 (sh ipv6 route)
---------------------------------------------
cnc1#sh ipv6 route
IPv6 Routing Table - Default - 5 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
EX - EIGRP external
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C 10::/64 [0/0]
via FastEthernet0/0, directly connected
L 10::10:2/128 [0/0]
via FastEthernet0/0, receive
OI 11::/64 [110/2]
via FE80::C801:DFF:FE8C:0, FastEthernet0/0
OI 12::/64 [110/3]
via FE80::C801:DFF:FE8C:0, FastEthernet0/0
L FF00::/8 [0/0]
via Null0, receive
cnc1#
cnc2#sh ipv6 route
IPv6 Routing Table - Default - 6 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
EX - EIGRP external
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C 10::/64 [0/0]
via FastEthernet0/0, directly connected
L 10::10:1/128 [0/0]
via FastEthernet0/0, receive
C 11::/64 [0/0]
via FastEthernet1/0, directly connected
L 11::11:1/128 [0/0]
via FastEthernet1/0, receive
OI 12::/64 [110/2]
via FE80::C802:CFF:FE24:1C, FastEthernet1/0
L FF00::/8 [0/0]
via Null0, receive
cnc2#
cnc3#sh ipv6 route
IPv6 Routing Table - Default - 6 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
EX - EIGRP external
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
OI 10::/64 [110/2]
via FE80::C801:DFF:FE8C:1C, FastEthernet1/0
C 11::/64 [0/0]
via FastEthernet1/0, directly connected
L 11::11:2/128 [0/0]
via FastEthernet1/0, receive
C 12::/64 [0/0]
via FastEthernet0/0, directly connected
L 12::12:1/128 [0/0]
via FastEthernet0/0, receive
L FF00::/8 [0/0]
via Null0, receive
cnc3#
cnc4#sh ipv6 route
IPv6 Routing Table - Default - 5 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
EX - EIGRP external
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
OI 10::/64 [110/3]
via FE80::C802:CFF:FE24:0, FastEthernet0/0
OI 11::/64 [110/2]
via FE80::C802:CFF:FE24:0, FastEthernet0/0
C 12::/64 [0/0]
via FastEthernet0/0, directly connected
L 12::12:2/128 [0/0]
via FastEthernet0/0, receive
L FF00::/8 [0/0]
via Null0, receive
cnc4#
---------------------------------------------
how to check 3 (ping and treceroute)
---------------------------------------------
cnc1#ping ipv6
Target IPv6 address: 12::12:2
Repeat count [5]: 100
Datagram size [100]:
Timeout in seconds [2]:
Extended commands? [no]:
Type escape sequence to abort.
Sending 100, 100-byte ICMP Echos to 12::12:2, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Success rate is 100 percent (100/100), round-trip min/avg/max = 164/312/452 ms
cnc1#
cnc1#traceroute 12::12:2
Type escape sequence to abort.
Tracing the route to 12::12:2
1 10::10:1 548 msec 96 msec 316 msec
2 11::11:2 160 msec 124 msec 64 msec
3 12::12:2 244 msec 192 msec 132 msec
cnc1#
cnc4#ping ipv6
Target IPv6 address: 10::10:2
Repeat count [5]: 100
Datagram size [100]:
Timeout in seconds [2]:
Extended commands? [no]:
Type escape sequence to abort.
Sending 100, 100-byte ICMP Echos to 10::10:2, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!
!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!
Success rate is 98 percent (98/100), round-trip min/avg/max = 28/416/1844 ms
cnc4#
cnc4#traceroute 10::10:2
Type escape sequence to abort.
Tracing the route to 10::10:2
1 12::12:1 328 msec 212 msec 164 msec
2 11::11:1 260 msec 572 msec 236 msec
3 10::10:2 1048 msec 1064 msec 596 msec
cnc4#
---------------------------------------------
sekarang belajar bagaimana agar di area 3 adalah
totally stub, langkah-langkahnya:
---------------------------------------------
cnc3(config)#ipv6 router ospf 1
cnc3(config-rtr)#area 3 stub no-summary
cnc3(config-rtr)#
cnc4(config)#ipv6 router ospf 1
cnc4(config-rtr)#area 3 stub
cnc4(config-rtr)#
---------------------------------------------
how to check....adakah perbedaannya ?
tentu ada...
---------------------------------------------
cnc4#sh ipv6 route
IPv6 Routing Table - Default - 4 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
EX - EIGRP external
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
OI ::/0 [110/2]
via FE80::C802:CFF:FE24:0, FastEthernet0/0
C 12::/64 [0/0]
via FastEthernet0/0, directly connected
L 12::12:2/128 [0/0]
via FastEthernet0/0, receive
L FF00::/8 [0/0]
via Null0, receive
cnc4#
cnc4#ping 10::10:2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10::10:2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 184/268/328 ms
cnc4#
---------------------------------------------
---------------------------------------------
---------------------------------------------
ref: Cisco IOS IPv6 Configuration Guide
Release 12.4, url: http://www.cisco.com (mei 2010)
Abu.Aisyah [Blog] @_@ 
nice info mas,,,
mau nanya nih mas,,,
kalo mpls ipv6 (pakai routing ospfv3) itu settingannya seperti ipv4 (“#mpls label protocol ldp ” dan “#mpls ip”) atau beda mas??? ..
mohon bantuannya ,,makasih mas
tutorial mas sangat bagus sekali, saya udh mengikuti langkah-langkah di atas namun saya masih bingung, knp saat saya sh ipv6 route tidak muncul routing OSPFv3, apa yang harus saya lakukan..
mw tanya dong.. kl di jaringan IPv6 mw pake OSPF sama EIGRP, OSPF nya harus yg OSPFv3 ya? bagaimana dgn EIGRPnya? makasih sebelumnya
kalau eigrp pake eigrp untuk ipv6, contohnya bisa lihat di sini:
https://iwing.wordpress.com/black-box/belajar-mengkonfigurasi-basic-eigrp-untuk-ipv6-di-router-cisco/