Skip to content

Belajar mengkonfigurasi OSPF over NBMA POINT TO POINT mode (PtP)

Belajar mengkonfigurasi OSPF over NBMA POINT TO POINT mode (PtP).
Topology yang digunakan adalah sebagai berikut:
------------------------------------------------
 
                               lo 100 192.168.40.0/24 
                                        +------+               
                                        !      !                    
                                        !(cnc2)!
                                        !      !                   
 s1/0.1 192.168.20.1/24                 +------+   
                                          / s1/0.1 
                 dlci 101 ---> dlci 202  /
                                        /    
 lo 100 192.168.10.0/24                /       
          +------+                +------+
          !      !s1/0            !      !        
          !(cnc1)!----------------! FRS  !
          !      !                !      !        
          +------+                +------+
 s1/0.2 192.168.30.1/24                \
                                        \       
                 dlci 102 ---> dlci 203  \
                                          \
                                           \s1/0.1
                                        +------+               
                                        !      !                    
                                        !(cnc3)!
                                        !      !                   
                                        +------+  
                                 lo 100 192.168.50.0/24
------------------------------------------------
S1/0.1 cnc1 192.168.20.1/24
S1/0.2 cnc1 192.168.30.1/24
S1/0.1 cnc2 192.168.20.2/24
S1/0.1 cnc3 192.168.30.2/24 
------------------------------------------------
Sebelumnya kita review sedikit mengenai sifat OSPF
PtP ini, sifat-sifatnya adalah :

-no DR/BDR elected
-uses separated sub-interfaces
-requires diffrent subnet
-Neighbours automatically form

ok, langkah-langkahnya adalah sebagai berikut:
------------------------------------------------
1. Konfigurasi addressing
------------------------------------------------
cnc1#

interface Serial1/0
 no ip address
 encapsulation frame-relay
 serial restart-delay 0
 no arp frame-relay
 no frame-relay inverse-arp
!
interface Serial1/0.1 point-to-point
 ip address 192.168.20.1 255.255.255.0
 frame-relay interface-dlci 101
!
interface Serial1/0.2 point-to-point
 ip address 192.168.30.1 255.255.255.0
 frame-relay interface-dlci 102
!
cnc1#
------------------------------------------------
cnc2#
!
interface Serial1/0
 no ip address
 encapsulation frame-relay
 serial restart-delay 0
 no arp frame-relay
 no frame-relay inverse-arp
!
interface Serial1/0.1 point-to-point
 ip address 192.168.20.2 255.255.255.0
 frame-relay interface-dlci 202
!

cnc2#
------------------------------------------------
cnc3#
!
interface Serial1/0
 no ip address
 encapsulation frame-relay
 serial restart-delay 0
 no arp frame-relay
 no frame-relay inverse-arp
!
interface Serial1/0.1 point-to-point
 ip address 192.168.30.2 255.255.255.0
 frame-relay interface-dlci 203
!
cnc3#
------------------------------------------------
2.how to check 1 (sh frame-relay map)
------------------------------------------------
cnc1#show frame-relay map
Serial1/0.2 (up): point-to-point dlci, dlci 102(0x66,0x1860), broadcast
 status defined, active
Serial1/0.1 (up): point-to-point dlci, dlci 101(0x65,0x1850), broadcast
 status defined, active
cnc1#

cnc2#show frame-relay map
Serial1/0.1 (up): point-to-point dlci, dlci 202(0xCA,0x30A0), broadcast
 status defined, active
cnc2#

cnc3#sh frame-relay map
Serial1/0.1 (up): point-to-point dlci, dlci 203(0xCB,0x30B0), broadcast
 status defined, active
cnc3#
------------------------------------------------
3. Konfigurasi OSPF  
------------------------------------------------
cnc1#
!
router ospf 1
 router-id 1.1.1.1
 log-adjacency-changes
 network 192.168.10.0 0.0.0.255 area 0
 network 192.168.20.0 0.0.0.255 area 0
 network 192.168.30.0 0.0.0.255 area 0
!
cnc1#
------------------------------------------------
cnc2#
!
router ospf 1
 router-id 2.2.2.2
 log-adjacency-changes
 network 192.168.20.0 0.0.0.255 area 0
 network 192.168.40.0 0.0.0.255 area 0
!
cnc2#
------------------------------------------------
cnc3#
!
router ospf 1
 router-id 3.3.3.3
 log-adjacency-changes
 network 192.168.30.0 0.0.0.255 area 0
 network 192.168.50.0 0.0.0.255 area 0
!
cnc3#
------------------------------------------------
4.how to check 2 (sh ip ospf interface)
------------------------------------------------
cnc1#sh ip ospf interface
Serial1/0.2 is up, line protocol is up
 Internet Address 192.168.30.1/24, Area 0
 Process ID 1, Router ID 1.1.1.1, Network Type POINT_TO_POINT, Cost: 64
 Transmit Delay is 1 sec, State POINT_TO_POINT,
 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
 oob-resync timeout 40
 Hello due in 00:00:04
 Supports Link-local Signaling (LLS)
 Index 2/2, flood queue length 0
 Next 0x0(0)/0x0(0)
 Last flood scan length is 1, maximum is 1
 Last flood scan time is 0 msec, maximum is 0 msec
 Neighbor Count is 1, Adjacent neighbor count is 1
 Adjacent with neighbor 3.3.3.3
 Suppress hello for 0 neighbor(s)
Serial1/0.1 is up, line protocol is up
 Internet Address 192.168.20.1/24, Area 0
 Process ID 1, Router ID 1.1.1.1, Network Type POINT_TO_POINT, Cost: 64
 Transmit Delay is 1 sec, State POINT_TO_POINT,
 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
 oob-resync timeout 40
 Hello due in 00:00:00
 Supports Link-local Signaling (LLS)
 Index 1/1, flood queue length 0
 Next 0x0(0)/0x0(0)
 Last flood scan length is 1, maximum is 1
 Last flood scan time is 0 msec, maximum is 0 msec
 Neighbor Count is 1, Adjacent neighbor count is 1
 Adjacent with neighbor 2.2.2.2
 Suppress hello for 0 neighbor(s)
cnc1#

cnc2#sh ip ospf interface
Loopback100 is up, line protocol is up
 Internet Address 192.168.40.1/24, Area 0
 Process ID 1, Router ID 2.2.2.2, Network Type LOOPBACK, Cost: 1
 Loopback interface is treated as a stub Host
Serial1/0.1 is up, line protocol is up
 Internet Address 192.168.20.2/24, Area 0
 Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 64
 Transmit Delay is 1 sec, State POINT_TO_POINT,
 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
 oob-resync timeout 40
 Hello due in 00:00:08
 Supports Link-local Signaling (LLS)
 Index 1/1, flood queue length 0
 Next 0x0(0)/0x0(0)
 Last flood scan length is 1, maximum is 1
 Last flood scan time is 0 msec, maximum is 0 msec
 Neighbor Count is 1, Adjacent neighbor count is 1
 Adjacent with neighbor 1.1.1.1
 Suppress hello for 0 neighbor(s)
cnc2#

cnc3#sh ip ospf interface
Loopback100 is up, line protocol is up
 Internet Address 192.168.50.1/24, Area 0
 Process ID 1, Router ID 3.3.3.3, Network Type LOOPBACK, Cost: 1
 Loopback interface is treated as a stub Host
Serial1/0.1 is up, line protocol is up
 Internet Address 192.168.30.2/24, Area 0
 Process ID 1, Router ID 3.3.3.3, Network Type POINT_TO_POINT, Cost: 64
 Transmit Delay is 1 sec, State POINT_TO_POINT,
 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
 oob-resync timeout 40
 Hello due in 00:00:04
 Supports Link-local Signaling (LLS)
 Index 1/1, flood queue length 0
 Next 0x0(0)/0x0(0)
 Last flood scan length is 1, maximum is 1
 Last flood scan time is 0 msec, maximum is 0 msec
 Neighbor Count is 1, Adjacent neighbor count is 1
 Adjacent with neighbor 1.1.1.1
 Suppress hello for 0 neighbor(s)
cnc3#
------------------------------------------------
5.how to check 3 (sh ip ospf neighbor),no DR/BDR
elected.
------------------------------------------------
cnc1#sh ip ospf neighbor

Neighbor ID     Pri   State           Dead Time   Address         Interface
3.3.3.3           0   FULL/  -        00:00:38    192.168.30.2    Serial1/0.2
2.2.2.2           0   FULL/  -        00:00:37    192.168.20.2    Serial1/0.1
cnc1#

cnc2#sh ip ospf neighbor

Neighbor ID     Pri   State           Dead Time   Address         Interface
1.1.1.1           0   FULL/  -        00:00:28    192.168.20.1    Serial1/0.1
cnc2#

cnc3#sh ip ospf neighbor

Neighbor ID     Pri   State           Dead Time   Address         Interface
1.1.1.1           0   FULL/  -        00:00:21    192.168.30.1    Serial1/0.1
cnc3#
------------------------------------------------
6.how to check 4 (sh ip route)
------------------------------------------------
cnc1#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
 D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
 N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
 E1 - OSPF external type 1, E2 - OSPF external type 2
 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
 ia - IS-IS inter area, * - candidate default, U - per-user static route
 o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.30.0/24 is directly connected, Serial1/0.2
 191.168.0.0/24 is subnetted, 1 subnets
C       191.168.10.0 is directly connected, Loopback100
 192.168.40.0/32 is subnetted, 1 subnets
O       192.168.40.1 [110/65] via 192.168.20.2, 00:13:34, Serial1/0.1
C    192.168.20.0/24 is directly connected, Serial1/0.1
 192.168.50.0/32 is subnetted, 1 subnets
O       192.168.50.1 [110/65] via 192.168.30.2, 00:13:34, Serial1/0.2
cnc1#

cnc2#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
 D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
 N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
 E1 - OSPF external type 1, E2 - OSPF external type 2
 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
 ia - IS-IS inter area, * - candidate default, U - per-user static route
 o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

O    192.168.30.0/24 [110/128] via 192.168.20.1, 00:28:42, Serial1/0.1
C    192.168.40.0/24 is directly connected, Loopback100
C    192.168.20.0/24 is directly connected, Serial1/0.1
 192.168.50.0/32 is subnetted, 1 subnets
O       192.168.50.1 [110/129] via 192.168.20.1, 00:28:42, Serial1/0.1
cnc2#

cnc3#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
 D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
 N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
 E1 - OSPF external type 1, E2 - OSPF external type 2
 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
 ia - IS-IS inter area, * - candidate default, U - per-user static route
 o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.30.0/24 is directly connected, Serial1/0.1
 192.168.40.0/32 is subnetted, 1 subnets
O       192.168.40.1 [110/129] via 192.168.30.1, 00:29:06, Serial1/0.1
O    192.168.20.0/24 [110/128] via 192.168.30.1, 00:29:06, Serial1/0.1
C    192.168.50.0/24 is directly connected, Loopback100
cnc3#
------------------------------------------------
8.how to check 5 (ping)
------------------------------------------------
cnc2#pi
Protocol [ip]:
Target IP address: 192.168.50.1
Repeat count [5]: 100
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 100, 100-byte ICMP Echos to 192.168.50.1, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Success rate is 98 percent (98/100), round-trip min/avg/max = 116/475/1616 ms
cnc2#
------------------------------------------------
"sekian dulu, semoga bermanfaat, CMIIW and salam
sedogedoi"
ref:
[1]. Cisco IOS IP Routing Protocols
Configuration Guide, http://www.cisco.com, (juni 2010)

No comments yet

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: